<span id="5fxhx"><listing id="5fxhx"><meter id="5fxhx"></meter></listing></span>
<address id="5fxhx"><mark id="5fxhx"></mark></address>
    <menuitem id="5fxhx"><font id="5fxhx"></font></menuitem>

    <form id="5fxhx"></form>

    <strike id="5fxhx"><output id="5fxhx"></output></strike>

      <var id="5fxhx"><dfn id="5fxhx"></dfn></var>
      <ins id="5fxhx"><noframes id="5fxhx"><pre id="5fxhx"></pre>

      <menuitem id="5fxhx"></menuitem>

          <nobr id="5fxhx"><dfn id="5fxhx"><cite id="5fxhx"></cite></dfn></nobr>

          歡迎光臨 [ 無錫市駿德冶金設備有限公司 ] 官網!

          網站地圖 聯系我們

          無錫市駿德冶金設備有限公司

          銷售熱線

          138 0618 6056

          堆焊為您介紹該技術的優缺點及應用范圍

                 無錫市駿德冶金設備有限公司為您提供最優質的產品。
                 帶極電渣堆焊與帶極埋弧堆焊比有以下優點:
                 1)熔深淺而均勻,母材稀釋率低,一般可控制在10%以下,比埋弧焊小一倍、單層堆焊即可滿足性能要求;
                 2)熔敷效率高,在中等電流下,比埋弧焊高50%;
                 3)堆焊層成形良好,不易有夾渣等缺陷,表面質量優良,表面不平度小于0.5mm(埋弧堆焊時大于lmm)故表面無需機械加工,省料省時。
                 4)帶極中合金元素燒損和不利元素增量極少,堆焊層的塑性和韌性高于埋弧難焊。
                 5)由于接頭熔合區的碳擴散層窄,馬氏體帶寬度小,故接頭熔合區性能優于帶極埋弧堆焊。
                 正由于帶極電渣堆焊有上述優點,近年來國內外在加氫控制反應器、煤氣工程熱壁交換爐、核電站設備中壓力容器的內表面大面積堆焊中均得到了廣泛應用。
                 由于電渣帶圾堆焊自身的一些特點,它也有定的應用范圍:
                 帶極電渣堆焊熱輸入較高,故一般用于堆焊50~200mm的厚壁工件。

          上一篇:等離子弧堆焊技術

          下一篇:沒有了

          亚洲mv国产mv在线mv综合试看_亚洲A∨无码一区二区三区_91久久精品美女高潮喷水_中文字幕无码精品
          <span id="5fxhx"><listing id="5fxhx"><meter id="5fxhx"></meter></listing></span>
          <address id="5fxhx"><mark id="5fxhx"></mark></address>
            <menuitem id="5fxhx"><font id="5fxhx"></font></menuitem>

            <form id="5fxhx"></form>

            <strike id="5fxhx"><output id="5fxhx"></output></strike>

              <var id="5fxhx"><dfn id="5fxhx"></dfn></var>
              <ins id="5fxhx"><noframes id="5fxhx"><pre id="5fxhx"></pre>

              <menuitem id="5fxhx"></menuitem>

                  <nobr id="5fxhx"><dfn id="5fxhx"><cite id="5fxhx"></cite></dfn></nobr>